GorbaDisplay: Difference between revisions

From RevSpace
Jump to navigation Jump to search
Line 45: Line 45:
|+Connections
|+Connections
|-
|-
!Pin!!Name!!Remark
!Pin!!Id!!Remark
|-
|-
|1||?||Power or ground
|1||?||Power or ground
Line 55: Line 55:
|4||?||
|4||?||
|-
|-
|5||?||A1 of row multiplexer
|5||COL_SEL1||A1 of row multiplexer
|-
|-
|6||?||A2 of row multiplexer
|6||COL_SEL2||A2 of row multiplexer
|-
|-
|7||?||
|7||?||
Line 65: Line 65:
|9||?||
|9||?||
|-
|-
|10||?||A0 of row multiplexer
|10||COL_SEL0||A0 of row multiplexer
|-
|-
|11||?||
|11||?||
|-
|-
|12||?||SRCK of column shift register
|12||ROW_CLK||SRCK of column shift register
|-
|-
|13||?||Power or ground
|13||?||Power or ground

Revision as of 11:11, 2 August 2023

Project GorbaDisplay
File:Whyunopicture.jpg
Public transport LED display
Status Initializing
Contact bertrik, User:Eloy
Last Update 2023-08-02

Introduction

This project is about reverse engineering a former public transport LED display. It consists of Z panels of each X * 16 LEDs. Each panel has 16 amber LEDs vertically.

The plan is to make the display fully addressable as a bitmap display over a network connection, preferably with individually controllable brightness.

Hardware

14-pin header + chips

This thing consists of two main parts:

  • a control board, with logic to receive (for example) text messages over a serial connection and convert them to a bitmap display on the display board
  • a display board, with logic to light up each LED

Between them is a 14-pin connector, probably carrying the low-level LED control signals.

The display board consists of several (4?) panels of LEDs.

It has a light sensor to sense the ambient light level.

Theory of operation

My guess this is probably another row-multiplexed display. The display can light up one row at a time. By quickly lighting up each row in succession, the illusion to a human observer is that all LEDs are controlled simultaneously.

The display board contains the following integrated cicruits:

  • 74HC541, an octal buffer/line driver, probably buffers all signals coming in from the 14-pin connector to the rest of the electronic on the display board
  • 74HC238, a 3-to-8 line decoder/demultiplexer, probably selects which row is currently being lit up
  • group of 4x IRF7425, power MOSFET, probably for driving a row of LEDs with
  • a whole bunch of TPIC6C596, 8-bit shift register, probably drives the columns inside one row of LEDs

The demultiplexer handles only 3 bits, enough for 8 rows. Perhaps there are two of them to handle 16 rows: one for the top 8 rows and one for the bottom 8 rows.

14-pin connector

My guess for the pinout so far is:

Connections
Pin Id Remark
1 ? Power or ground
2 ? Power or ground
3 ?
4 ?
5 COL_SEL1 A1 of row multiplexer
6 COL_SEL2 A2 of row multiplexer
7 ?
8 ?
9 ?
10 COL_SEL0 A0 of row multiplexer
11 ?
12 ROW_CLK SRCK of column shift register
13 ? Power or ground
14 ? Power or ground


There are possibly pins for:

  • row select, bit 0
  • row select, bit 1
  • row select, bit 2
  • row select, bit 3
  • row-enable
  • shift register data
  • shift-register clear
  • shift-register data
  • analog LDR value
  • remote control input
  • power pin
  • ground pin

Software