LoRa-E5-mini: Difference between revisions

From RevSpace
Jump to navigation Jump to search
Line 73: Line 73:
** cd stm32
** cd stm32
** git clone https://github.com/bertrik/Arduino_Core_STM32
** git clone https://github.com/bertrik/Arduino_Core_STM32
* Under menu Tools/Board/STM32 boards .... *(sketchbook)*, choose 'Generic STM32WL series' from 'Generic STM32WL series'
* Under menu Tools/Board/STM32 boards .... <b>(sketchbook)</b>, choose 'Generic STM32WL series' from 'Generic STM32WL series'
* Under menu Tools/Board part number, choose 'Seeed Studios LoRa E5 mini'
* Under menu Tools/Board part number, choose 'Seeed Studios LoRa E5 mini'
* Install STM Cube for the upload tools, they are called en.stm32cubeprg-lin_v2-8-0_v2.8.0.zip
* Install STM Cube for the upload tools, they are called en.stm32cubeprg-lin_v2-8-0_v2.8.0.zip
Line 82: Line 82:
* Load the helloworld.ino file into the Arduino IDE:
* Load the helloworld.ino file into the Arduino IDE:
** Compile and upload with ctrl-U
** Compile and upload with ctrl-U
** Open serial port with ctrl-shift-M and see that serial messages are coming in  
** Open serial port with ctrl-shift-M and see that serial messages are coming in


==== Programming over SWD ====
==== Programming over SWD ====

Revision as of 06:30, 18 October 2021

Project LoRa E5
Arduino on the LoRa-E5-mini devboard
Status In progress
Contact bertrik
Last Update 2021-10-18

The plan

This page is about the LoRa-E5 module and getting it to work as a LoRaWAN node with Arduino and the BasicMac stack.

  • replace the original "AT" firmware with Arduino based firmware
  • use the BasicMac library for LoRaWAN
  • use platformio as the build system
  • create some basic examples for use as a LoRaWAN node on TheThingsNetwork

Interesting post about this module: https://www.disk91.com/2021/technology/lora/lora-e5-the-seeed-studio-stm32-wl-module/

What currently works:

  • can run an Arduino program, compiling from the Arduino IDE
  • blinking the LED works
  • output over serial works

TODO, yet to figure out:

  • add support for the Seeed LoRa E5 mini in the stm32 package
  • get communication going using the internal "subghz" SPI port
    • do I need to enable the APB3 clock domain?
    • get a simple transfer going that proves that meaningful data is exchanged (e.g. default sync word magic number)
  • get basicmac stack working with the "subghz" SPI port (it appears all communication is done using just "SPI")
  • get compilation and upload working with platformio

Hardware

The hardware is the LoRa-E5 mini from seeed studio, contains the STM32WLE5JC:

Overview of pins used on this board (not completely standard): https://wiki.seeedstudio.com/LoRa_E5_mini/#22-gpio-configuration-overview

LoRa modem

It appears the LoRa functionality is exposed through an internal SPI bus, called SUBGHZSPI in the datasheet.

Also, there are some pins to control the radio path.

Software

Initial experimental firmware can be found at: https://github.com/bertrik/lora-e5

  • blinky example, the most basic of all sketches which makes a LED blink demonstration of successful download of an Arduino program
  • helloworld example, sends a text over the serial port

These examples still uses the Arduino IDE, with a 'generic' STM32WLE5JCI.

There appears to be support for various kinds of WL55 boards in the stm32duino project: https://github.com/stm32duino/Arduino_Core_STM32/blob/main/boards.txt

Support for a generic WLE5JCI board here in the stm32duino archive: https://github.com/stm32duino/Arduino_Core_STM32/blob/main/variants/STM32WLxx/WL54JCI_WL55JCI_WLE4J(8-B-C)I_WLE5J(8-B-C)I/boards_entry.txt#L62

How to add a new variant (board): https://github.com/stm32duino/wiki/wiki/Add-a-new-variant-(board)

Experimental development environment

This uses my own fork, which will include support for the Seeed LoRa E5 mini.

Now you can:

  • Load the helloworld.ino file into the Arduino IDE:
    • Compile and upload with ctrl-U
    • Open serial port with ctrl-shift-M and see that serial messages are coming in

Programming over SWD

Connect an ST-LINKv2 as follows:

  • SWDIO to PA13
  • SWCLK to PA14
  • GND to GND

Getting it to work

Got a flashing LED sketch to work:

  • install Arduino IDE, e.g. 1.8.16
  • install the STM32 support
    • add through menu File / Preferences / Additional board manager URLs
 https://github.com/stm32duino/BoardManagerFiles/raw/main/package_stmicroelectronics_index.json
    • under menu Tools / Board / Board manager, search for stm32 and install the board package
  • select the right board:
    • WLE5JCIx
  • upgrade the firmware of my stlink2 (tool from ST), currently at V2J38S7
  • run the cubestm environment to use the stlink2 to disable the firmware protection
  • flash a simple blinky sketch to the board

Serial port does not work yet, it is connected to PB6/PB7. I need to configure an alternative setting for the pins, don't know exactly how to do that on Arduino:

Node configuration in TheThingsNetwork

The information on the website of Seeed studios is outdated. It refers to the "v2" version of TheThingsNetwork, which is being phased out. It is already impossible to add new nodes on TTNv2, since it was set to read-only.

Nodes should be configured for TheThingsNetwork v3 instead.