Uploads van Mahjongg
Uit RevSpace
Op deze speciale pagina zijn alle toegevoegde bestanden te bekijken.
| Datum | Naam | Miniatuur | Grootte | Beschrijving | Versies |
|---|---|---|---|---|---|
| 1 aug 2018 23:45 | Schermafdruk van 2018-08-02 01-16-22.png (bestand) |  |
209 kB | partly laid out (expansion port, Z80 data and address, and SRAM data and address) | 1 |
| 1 aug 2018 23:31 | RHOCOCO-PROP Rev1.2.pdf (bestand) |  |
181 kB | swapped expansion port vertically. (pin 1 left) and swapped both address and data lines for SRAM chip (including A17) to optimize layout routing (on top side only) | 1 |
| 1 aug 2018 19:50 | Schermafdruk van 2018-08-01 21-11-59.png (bestand) |  |
208 kB | placement completed of rhococo rev 1.1 | 1 |
| 1 aug 2018 19:25 | RHOCOCO PROP rev1.1.pdf (bestand) | |
175 kB | corrected databus | 1 |
| 1 aug 2018 01:01 | Screenshot 2018-08-01 02-59-00.png (bestand) |  |
174 kB | screenshot of KiCad layout editor during placement of Rhococo parts | 1 |
| 1 aug 2018 00:41 | Full RHOCOCO rev 1.0.pdf (bestand) | |
172 kB | rotated pin-header 180 degrees, changed audio connector symbol | 1 |
| 27 jul 2018 17:32 | Preview rhococo fitted on a 10 x 10cm PCB.PNG (bestand) |  |
227 kB | DB9 moved down EEPROM moved up | 5 |
| 27 jul 2018 13:49 | Preview rhococo fitted on a 10 x 10cm PCB back.PNG (bestand) |  |
35 kB | With 600 mil wide RAM | 3 |
| 24 jul 2018 23:24 | FULL RHOCOCO.pdf (bestand) | |
171 kB | Full compliment of schematics sheets of Z80 plus Propeller based Rhococo retro home color computer | 1 |
| 20 jul 2018 12:45 | KEYBOARD WITHOUT CAPS.PNG (bestand) |  |
505 kB | moved female headers to correct positions, added mounting holes | 2 |
| 20 jul 2018 10:24 | Rhococo keyboard.pdf (bestand) | |
262 kB | finished | 2 |
| 18 jul 2018 17:08 | RHOCOCO KEYBOARD with Joystick.png (bestand) |  |
96 kB | name correction | 1 |
| 18 jul 2018 17:01 | RHOCOCCO MAIN PROPELLER.png (bestand) |  |
147 kB | Name correction | 1 |
| 18 jul 2018 16:42 | RHOCOCO KEYBOARD with Joystick.pdf (bestand) | |
32 kB | Name corrected | 1 |
| 18 jul 2018 16:39 | RHOCOCO Z80CPU with RAM.pdf (bestand) | |
97 kB | Name correction | 1 |
| 18 jul 2018 16:37 | RHOCOCO MAIN PROPELLER.pdf (bestand) | |
94 kB | Name correction | 1 |
| 18 jul 2018 09:23 | RHOCOCCO KEYBOARD with Joystick.png (bestand) |  |
96 kB | First version, actual matrix configuration will come later, as its on a separate PCB. Heavily based on the ZX81/Spectrum concept. Expanded column header with one position, this makes an cursor key arrangement and extra keys possible. | 1 |
| 18 jul 2018 09:17 | RHOCOCO Z80 and RAM.png (bestand) |  |
167 kB | made several small corrections and changes, added expansion port (based on the ZX81 for now, but it will probably change in the future) | 3 |
| 18 jul 2018 09:12 | RHOCOCO MAIN PROP-.PNG (bestand) |  |
147 kB | Added power supply, analog audio with speaker driver, IO expander with SD-Card, serial I/O header for programming propeller and debugging. | 3 |
| 17 jul 2018 23:49 | KEYBOARD-z80ram-KEYBOARD.pdf (bestand) | |
28 kB | First version of keyboard I/O with joystick interface | 1 |
| 17 jul 2018 23:47 | RHOCOCCO Z80CPU with RAM.pdf (bestand) | |
89 kB | new version with expansion connector, and various corrections | 3 |
| 17 jul 2018 23:44 | RHOCOCO MAIN PROP.pdf (bestand) | |
87 kB | new main, with power supply, sound, IO expander with SD-card, Serial interface | 3 |
| 3 jul 2018 22:32 | RHOCOCCO Z80CPU+RAM.pdf (bestand) | |
44 kB | Z80 (5V) subsystem with RAM, and low address readout store | 1 |
| 28 mei 2018 16:06 | Mini80b.pdf (bestand) | |
56 kB | basic CP/M system with z80 and propeller chip | 1 |
| 22 mei 2018 22:35 | RHOCOCO with propeller.pdf (bestand) | |
67 kB | New version of RHOCOCCO, that uses a Parallax Propeller (PX32A) chip instead of an ATMEGA chip. | 1 |
| 18 apr 2018 10:01 | SNES JOYPAD WH PCB.png (bestand) |  |
398 kB | Like the old joypad for the zero, but this is for the zero WH, with headers on the TOP (not bottom), so new wiring to rotated/mirrored GPIO connector is needed | 1 |
| 11 apr 2018 13:51 | PCB bicicle backlight bottom side.PNG (bestand) |  |
363 kB | unassigned Via's connected to GND | 2 |
| 27 mrt 2018 20:22 | RF Achterlicht rev2.1.png (bestand) |  |
250 kB | 2 | |
| 27 mrt 2018 20:16 | Rfachterlicht rev 2.3.pdf (bestand) | |
79 kB | 2 | |
| 7 mrt 2018 11:49 | PCB bicicle backlight top side.PNG (bestand) |  |
228 kB | added static cap, and SMT coil | 3 |
| 21 feb 2018 00:10 | SNES JOYPAD WITH ZERO WH.pdf (bestand) | |
68 kB | Revised version for PI Zero WH (with headers on top side) | 1 |
| 20 feb 2018 21:28 | Rfbacklight 3D view.png (bestand) |  |
214 kB | final touches silkscreen text, address data text, copyright message, changed diode to 1N4148 type | 3 |
| 20 feb 2018 21:25 | Rf achterlicht rev 2,2.pdf (bestand) | |
70 kB | 2 | |
| 30 jan 2018 23:13 | Componenten opstelling rf backlight rev 2,2.pdf (bestand) | |
73 kB | Reverted to version as of 23:12, 30 January 2018 | 3 |
| 16 jan 2018 22:24 | Achterlicht.jpg (bestand) |  |
29 kB | 1 | |
| 16 jan 2018 22:12 | RF achterlicht 2,0.png (bestand) |  |
233 kB | 2 | |
| 16 jan 2018 22:06 | RF Achterlicht rev2.1.pdf (bestand) | |
67 kB | 1 | |
| 10 jan 2018 00:06 | Rfachterlicht2,0.pdf (bestand) | |
59 kB | 1 | |
| 29 nov 2017 10:53 | SNES JOYPAD PCB.png (bestand) |  |
307 kB | revision 1.0 | 1 |
| 22 nov 2017 10:44 | Right-angle-gold-rca-jack-pcb-mount-6.jpg (bestand) |  |
50 kB | 1 | |
| 22 nov 2017 10:35 | Snes joypad base.png (bestand) |  |
138 kB | top and bottom of SNES joypad base board | 1 |
| 14 nov 2017 23:45 | SNES JOYPAD BASE.png (bestand) |  |
7 kB | smaller version | 2 |
| 14 nov 2017 23:17 | SNES JOYPAD BASE.pdf (bestand) | |
22 kB | 1 | |
| 13 nov 2017 16:03 | Simplified pseudo random generator.png (bestand) |  |
13 kB | 1 | |
| 10 nov 2017 18:47 | Space invaders pseudo ruis generator.png (bestand) |  |
90 kB | 1 | |
| 10 nov 2017 18:39 | Space invaders pseudo ruis generator.pdf (bestand) | |
53 kB | 1 | |
| 25 okt 2017 10:20 | SNES JOYPAD preview unrouted.png (bestand) |  |
115 kB | Preview of the version I made using KiCAD where I tested if I could create gerber files, and could generate a suitable board shape with KiCad, and to check placement issues. No traces were yet laid out. | 1 |
| 17 okt 2017 22:15 | SNES JOYPAD PLACEMENT with dimensions cropped.png (bestand) |  |
97 kB | 1 | |
| 17 okt 2017 22:05 | SNES JOYPAD PLACEMENT with dimensions.pdf (bestand) | |
232 kB | 1 | |
| 10 okt 2017 22:40 | SNES JOYPAD schematic picture.png (bestand) |  |
152 kB | 1 |
