UVBox - Bewerkingsoverzicht

Juerd op 13 jan 2016 om 23:20

2016-01-13T23:20:35Z

← Oudere versie		Versie van 13 jan 2016 23:20
Regel 1:		Regel 1:
	{{Project		{{Project
	\|Name=UVBox		\|Name=UVBox
	\|Status=~~In progress~~		\|Status=Stalled
	\|Contact=user:Eddy Pronk		\|Contact=user:Eddy Pronk
	}}		}}

Eddy Pronk op 5 jun 2013 om 15:35

2013-06-05T15:35:43Z

← Oudere versie		Versie van 5 jun 2013 15:35
Regel 1:		Regel 1:
	{{Project		{{Project
	\|Name=UVBox		\|Name=UVBox
	\|Status=in progress		\|Status=In progress
	\|Contact=user:Eddy Pronk		\|Contact=user:Eddy Pronk
	}}		}}

Eddy Pronk: Project update June

2013-06-05T15:31:24Z

Project update June

← Oudere versie		Versie van 5 jun 2013 15:31
Regel 1:		Regel 1:
	{{Project		{{Project
	\|Name=UVBox		\|Name=UVBox
	\|Status=~~Initializing~~		\|Status=in progress
	\|Contact=user:Eddy Pronk		\|Contact=user:Eddy Pronk
	}}		}}
Regel 12:		Regel 12:
	== Status ==		== Status ==
	500 UV LEDs are currently on a boat from China towards the space. This should be enough for at least 1 decent size box and a tanning bed.		500 UV LEDs are currently on a boat from China towards the space. This should be enough for at least 1 decent size box and a tanning bed.

			Update June 2013: Almost finished soldering the boards. Each 10x16 prototype board contains 12 x 18 = 216 LEDs, and the enclosure will house 2 boards with 432 LEDs in total in a 20 x 16 configuration. For each 3 LEDs (in series) there is a single 68Ohm resistor. Total amperage per board is around 1.4A (observed).

Eddy Pronk op 25 apr 2013 om 07:47

2013-04-25T07:47:48Z

← Oudere versie		Versie van 25 apr 2013 07:47
Regel 7:		Regel 7:
	A cheap and simple UV exposure box for creating PCB's using the photoresist method. The current solution is huge and inconvenient.		A cheap and simple UV exposure box for creating PCB's using the photoresist method. The current solution is huge and inconvenient.

	The box will consist of a frame, a matrix of UV LEDs and a timer circuit. The solution will be geared towards 10x16cm copper clad boards, and will therefore have a small form factor. For the timer circuit I propose using one of my ATMEGA88's and an LCD module. The box will be powered by 12V and ~~with~~ 2 or 3 LEDs (depending on Vacross) I hope to keep wattage down.		The box will consist of a frame, a matrix of UV LEDs and a timer circuit. The solution will be geared towards 10x16cm copper clad boards, and will therefore have a small form factor. For the timer circuit I propose using one of my ATMEGA88's and an LCD module. The box will be powered by 12V and by putting LEDs in series (every 2 or 3 LEDs, depending on Vacross) I hope to keep wattage down.


	== Status ==		== Status ==
	500 UV LEDs are currently on a boat from China towards the space. This should be enough for at least 1 decent size box and a tanning bed.		500 UV LEDs are currently on a boat from China towards the space. This should be enough for at least 1 decent size box and a tanning bed.

Eddy Pronk: Initial description

2013-04-24T00:58:44Z

Initial description

Nieuwe pagina

{{Project
|Name=UVBox
|Status=Initializing
|Contact=user:Eddy Pronk
}}

A cheap and simple UV exposure box for creating PCB's using the photoresist method. The current solution is huge and inconvenient.

The box will consist of a frame, a matrix of UV LEDs and a timer circuit. The solution will be geared towards 10x16cm copper clad boards, and will therefore have a small form factor. For the timer circuit I propose using one of my ATMEGA88's and an LCD module. The box will be powered by 12V and with 2 or 3 LEDs (depending on Vacross) I hope to keep wattage down.

== Status ==
500 UV LEDs are currently on a boat from China towards the space. This should be enough for at least 1 decent size box and a tanning bed.