Esp32cam - Revision history

Bertrik Sikken: /* Hardware */

2021-07-31T14:49:18Z

Hardware

← Older revision		Revision as of 14:49, 31 July 2021
Line 16:		Line 16:
	* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]		* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]

	To install the camera, flip the black part of the camera connector ~~UP, insert~~ the camera connector (contacts towards the PCB), ~~then~~ flip the black part back into the flat position.		To install the camera:
			* flip the black part of the camera connector 90 degrees so it points up
			* place the camera connector, contacts towards the PCB, camera facing up
			* gently slide the connector in place (about 2 or 3 mm of travel), e.g. pushing with the screw driver onto the rigid part of the camera connector towards the white part of the PCB connector
			* flip the black part of the connector back into the flat position.

	Pins (ESP32 cam to USB serial converter):		Pins (ESP32 cam to USB serial converter):

2021-04-05T12:18:39Z

2020-02-06T13:03:54Z

platformio

← Older revision		Revision as of 13:03, 6 February 2020
Line 45:		Line 45:

	Platformio can be installed on a Debian Linux system as follows:		Platformio can be installed on a Debian Linux system as follows:
	sudo apt~~-get~~ install python-pip		sudo apt install python-pip
	sudo pip install platformio		sudo pip install platformio
	pio upgrade		pio upgrade

2019-02-05T19:47:53Z

Software

← Older revision		Revision as of 19:47, 5 February 2019
Line 30:		Line 30:
	* https://github.com/donny681/ESP32_CAMERA_QR		* https://github.com/donny681/ESP32_CAMERA_QR
	* [https://youtu.be/q7Z_XnBYFhY Step by step video guide to getting it up and running with Arduino IDE and the Expressif CameraWebServer example]		* [https://youtu.be/q7Z_XnBYFhY Step by step video guide to getting it up and running with Arduino IDE and the Expressif CameraWebServer example]
			* https://github.com/geeksville/TenDollarWebcam

	=== platformio ===		=== platformio ===

2019-02-04T23:02:36Z

← Older revision		Revision as of 23:02, 4 February 2019
Line 17:		Line 17:
	* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]		* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]

	To ~~flash~~ the ~~module~~, ~~do not forget~~ the ~~jumper between pins~~ IO0 ~~and~~ GND!		To install the camera, flip the black part of the camera connector UP, insert the camera connector (contacts towards the PCB), then flip the black part back into the flat position.

			Pins (ESP32 cam to USB serial converter):
			* ESP-32 5V to USB serial 5V
			* ESP-32 GND to USB serial GND
			* ESP-32 UAR to USB-serial TX
			* ESP-32 UAT to USB-serial RX
			* ESP-32 IO0 looped to ESP-32 GND (they are next to each other), you can use a jumper or a dupont wire. CLOSED for flashing, OPEN for running.

	== Software ==		== Software ==

2019-01-29T21:40:48Z

← Older revision		Revision as of 21:40, 29 January 2019
Line 3:		Line 3:
	\|Picture=ESP32-CAM.jpg		\|Picture=ESP32-CAM.jpg
	\|Omschrijving=Cheap webcams with Wifi, what could possibly go wrong?		\|Omschrijving=Cheap webcams with Wifi, what could possibly go wrong?
	\|Status=~~Initializing~~		\|Status=In progress
	\|Contact=noopwafel		\|Contact=noopwafel
	\|Contact1=Sebastius		\|Contact1=Sebastius
			\|Contact2=bertrik
	}}		}}

2019-01-29T19:58:13Z

platformio

← Older revision		Revision as of 19:58, 29 January 2019
Line 24:		Line 24:

	=== platformio ===		=== platformio ===
	~~[[bertrik]] made an attempt to build the~~ CameraWebServer example as a platformio project: https://github.com/bertrik/CameraWebServer		The CameraWebServer example can be compiled as a platformio project: https://github.com/bertrik/CameraWebServer

	To build the code, clone the git repo above, cd into it, then type		To build the code, clone the git repo above, cd into it, then type
	pio run		pio run

	To upload it to the board:		To upload it to the board (put a jumper between IO0 and GND):
	pio run -t upload		pio run -t upload

	To watch the debug output:		To watch the debug output (remove the jumper):
	pio device monitor		pio device monitor

2019-01-29T19:56:57Z

Hardware

← Older revision		Revision as of 19:56, 29 January 2019
Line 15:		Line 15:
	* http://wiki.aithinker.com/esp32-cam		* http://wiki.aithinker.com/esp32-cam
	* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]		* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]

			To flash the module, do not forget the jumper between pins IO0 and GND!

	== Software ==		== Software ==

2019-01-27T23:56:18Z

← Older revision		Revision as of 23:56, 27 January 2019
Line 32:		Line 32:
	To watch the debug output:		To watch the debug output:
	pio device monitor		pio device monitor

			Platformio can be installed on a Debian Linux system as follows:
			sudo apt-get install python-pip
			sudo pip install platformio
			pio upgrade

2019-01-27T22:58:17Z

@@ Line 9: / Line 9: @@
 * http://wiki.aithinker.com/esp32-cam
 * https://github.com/donny681/ESP32_CAMERA_QR
 * [https://youtu.be/q7Z_XnBYFhY Step by step video guide to getting it up and running with Arduino IDE and the Expressif CameraWebServer example]