RevSpace - User contributions [en-gb]

Flashforge AD5X

2026-07-12T21:05:41Z

Fluffyredpanda:

= Flashforge AD5X =

This page is a work in progress. Not all information may be correct yet. Please add information if you have used this 3D printer.

== Slicer ==

OrcaSlicer:
https://www.orcaslicer.com/

Flash Studio:
https://www.flashforge.com/pages/flash-studio-desktop

=== OrcaSlicer setup ===
Look at this page from step 16 onward if you want to use OrcaSlicer:
https://wiki.zmod.link/Setup/

<code>
Host Type: Octo/Klipper

Printer Agent: Moonraker

Hostname, IP or URL: <IP address>:7125

Device UI: <IP address>

</code>

Adding the :7125 port after the IP address is very important for this to work. On that port it will be able to recognize the Host Type. The device UI runs on port 80. So entering the IP address under Device UI will suffice.

=== Flash Studio instructions ===
1. Go to 'Device' Tab

[[File:Flash Studio adding 3d printer screenshot.png|thumb]]

2. Click on the '+' icon

3. Click under Other Device on AD5X

4. A popup will show. It will ask for the printer access code. This will show on the 3D printer itself under "Settings (gear icon) > Network (wifi icon) > Network Mode".

[[File:Screenshot 2026-07-12 223901.png|thumb]]

5. The FlashForge AD5X will now show up under 'Device List' in Flash Studio.

== WebUI ==
There is a web interface (Fluidd) available on the printers IP Address:

http://<IP-Address>

For example you can upload printer files or move the printer head.

== Firmware ==
=== ZMod ===
This is 'extra' firmware on top of the original printer. "Z-Mod doesn’t replace the stock firmware — it enhances it".
Comes with Klipper updates that the original firmware does not provide. The Zmod firmware also installs Fluidd which enables a WebUI on the printers IP address.

https://wiki.zmod.link/

Flashforge AD5X

2026-07-12T21:05:13Z

Fluffyredpanda:

= Flashforge AD5X =

This page is a work in progress. Not all information may be correct yet. Please add information if you have used this 3D printer.

== Slicer ==

OrcaSlicer:
https://www.orcaslicer.com/

Flash Studio:
https://www.flashforge.com/pages/flash-studio-desktop

=== OrcaSlicer setup ===
Look at this page from step 16 onward if you want to use OrcaSlicer:
https://wiki.zmod.link/Setup/

<code>
Host Type: Octo/Klipper
Printer Agent: Moonraker
Hostname, IP or URL: <IP address>:7125
Device UI: <IP address>
</code>

Adding the :7125 port after the IP address is very important for this to work. On that port it will be able to recognize the Host Type. The device UI runs on port 80. So entering the IP address under Device UI will suffice.

=== Flash Studio instructions ===
1. Go to 'Device' Tab

[[File:Flash Studio adding 3d printer screenshot.png|thumb]]

2. Click on the '+' icon

3. Click under Other Device on AD5X

4. A popup will show. It will ask for the printer access code. This will show on the 3D printer itself under "Settings (gear icon) > Network (wifi icon) > Network Mode".

[[File:Screenshot 2026-07-12 223901.png|thumb]]

5. The FlashForge AD5X will now show up under 'Device List' in Flash Studio.

== WebUI ==
There is a web interface (Fluidd) available on the printers IP Address:

http://<IP-Address>

For example you can upload printer files or move the printer head.

== Firmware ==
=== ZMod ===
This is 'extra' firmware on top of the original printer. "Z-Mod doesn’t replace the stock firmware — it enhances it".
Comes with Klipper updates that the original firmware does not provide. The Zmod firmware also installs Fluidd which enables a WebUI on the printers IP address.

https://wiki.zmod.link/

Flashforge AD5X

2026-07-12T20:57:03Z

Fluffyredpanda:

= Flashforge AD5X =

This page is a work in progress. Please add information if you have used this 3D printer.

== Slicer ==

OrcaSlicer:
https://www.orcaslicer.com/

Flash Studio:
https://www.flashforge.com/pages/flash-studio-desktop

=== OrcaSlicer setup ===
Look at this page from step 16 onward if you want to use OrcaSlicer:
https://wiki.zmod.link/Setup/

=== Flash Studio instructions ===
1. Go to 'Device' Tab

[[File:Flash Studio adding 3d printer screenshot.png|thumb]]

2. Click on the '+' icon

3. Click under Other Device on AD5X

4. A popup will show. It will ask for the printer access code. This will show on the 3D printer itself under "Settings (gear icon) > Network (wifi icon) > Network Mode".

[[File:Screenshot 2026-07-12 223901.png|thumb]]

5. The FlashForge AD5X will now show up under 'Device List' in Flash Studio.

== WebUI ==
There is a web interface (Fluidd) available on the printers IP Address:

http://<IP-Address>

For example you can upload printer files or move the printer head.

== Firmware ==
=== ZMod ===
This is 'extra' firmware on top of the original printer. "Z-Mod doesn’t replace the stock firmware — it enhances it".
Comes with Klipper updates that the original firmware does not provide. The Zmod firmware also installs Fluidd which enables a WebUI on the printers IP address.

https://wiki.zmod.link/

Flashforge AD5X

2026-07-12T20:44:33Z

Fluffyredpanda:

= Flashforge AD5X =

This page is a work in progress. Please add information if you have used this 3D printer.

== Slicer ==

OrcaSlicer:
https://www.orcaslicer.com/

Flash Studio:
https://www.flashforge.com/pages/flash-studio-desktop

=== Flash Studio instructions ===
1. Go to 'Device' Tab

[[File:Flash Studio adding 3d printer screenshot.png|thumb]]

2. Click on the '+' icon

3. Click under Other Device on AD5X

4. A popup will show. It will ask for the printer access code. This will show on the 3D printer itself under "Settings (gear icon) > Network (wifi icon) > Network Mode".

[[File:Screenshot 2026-07-12 223901.png|thumb]]

5. The FlashForge AD5X will now show up under 'Device List' in Flash Studio.

== WebUI ==
There is a web interface (Fluidd) available on the printers IP Address:

http://<IP-Address>

For example you can upload printer files or move the printer head.

== Firmware ==
=== ZMod ===
This is 'extra' firmware on top of the original printer. "Z-Mod doesn’t replace the stock firmware — it enhances it".
Comes with Klipper updates that the original firmware does not provide. The Zmod firmware also installs Fluidd which enables a WebUI on the printers IP address.

https://wiki.zmod.link/

Flashforge AD5X

2026-07-12T20:43:57Z

Fluffyredpanda:

= Flashforge AD5X =

This page is a work in progress. Please add information if you have used this 3D printer.

== Slicer ==

OrcaSlicer:
https://www.orcaslicer.com/

Flash Studio:
https://www.flashforge.com/pages/flash-studio-desktop

=== Flash Studio instructions ===
1. Go to 'Device' Tab

[[File:Flash Studio adding 3d printer screenshot.png|thumb]]

2. Click on the '+' icon

3. Click under Other Device on AD5X

4. A popup will show. It will ask for the printer access code. This will show on the 3D printer itself under "Settings (gear icon) > Network (wifi icon) > Network Mode".

[[File:Screenshot 2026-07-12 223901.png|thumb]]

5. The FlashForge AD5X will now show up under 'Device List' in FlashForge Studio.

== WebUI ==
There is a web interface (Fluidd) available on the printers IP Address:

http://<IP-Address>

For example you can upload printer files or move the printer head.

== Firmware ==
=== ZMod ===
This is 'extra' firmware on top of the original printer. "Z-Mod doesn’t replace the stock firmware — it enhances it".
Comes with Klipper updates that the original firmware does not provide. The Zmod firmware also installs Fluidd which enables a WebUI on the printers IP address.

https://wiki.zmod.link/

File:Screenshot 2026-07-12 223901.png

2026-07-12T20:39:19Z

Fluffyredpanda: File uploaded with MsUpload

File uploaded with MsUpload

File:Flash Studio adding 3d printer screenshot.png

2026-07-12T20:37:37Z

Fluffyredpanda:

Flash Studio adding 3d printer screenshot

3DPrinter

2026-07-12T20:26:26Z

Fluffyredpanda:

'''Bij RevSpace hebben wij de volgende 3D printers'''
* Bambu Lab X1 Carbon Combo. Zie de pagina [[Bambu_Lab_X1_Carbon]]
* FlashForge AD5X. Zie de pagina [[Flashforge_AD5X]]
* Prusa i3 MK3. Zie de pagina [[Prusai3mk3]]

3DPrinter

2026-07-12T20:25:59Z

Fluffyredpanda:

'''Bij RevSpace hebben wij de volgende 3D printers'''
* Bambu Lab X1 Carbon Combo. Zie de pagina [[Bambu_Lab_X1_Carbon]]
* FlashForge AD5X [[Flashforge_AD5X]]
* Prusa i3 MK3. Zie de pagina [[Prusai3mk3]]

Flashforge AD5X

2026-07-12T20:23:34Z

Fluffyredpanda: Created page with " = Flashforge AD5X = This page is a work in progress. Please add information if you have used this 3D printer. == Slicer == OrcaSlicer: https://www.orcaslicer.com/ Flash Studio: https://www.flashforge.com/pages/flash-studio-desktop Settings when adding: You can find == WebUI == There is a web interface (Fluidd) available on the printers IP Address: http://<IP-Address> For example you can upload printer files or move the printer head. == Firmware == === ZMod =..."

= Flashforge AD5X =

This page is a work in progress. Please add information if you have used this 3D printer.

== Slicer ==
OrcaSlicer:
https://www.orcaslicer.com/

Flash Studio:
https://www.flashforge.com/pages/flash-studio-desktop

Settings when adding:
You can find

== WebUI ==
There is a web interface (Fluidd) available on the printers IP Address:

http://<IP-Address>

For example you can upload printer files or move the printer head.

== Firmware ==
=== ZMod ===
This is 'extra' firmware on top of the original printer. "Z-Mod doesn’t replace the stock firmware — it enhances it".
Comes with Klipper updates that the original firmware does not provide. The Zmod firmware also installs Fluidd which enables a WebUI on the printers IP address.

https://wiki.zmod.link/