Difference between revisions of "Stofradar"

From RevSpace
Jump to navigation Jump to search
(Introduction)
(13 intermediate revisions by the same user not shown)
Line 3: Line 3:
 
   |Picture=Stofradar3.png
 
   |Picture=Stofradar3.png
 
   |Omschrijving=Visualizing atmospheric particulate matter concentrations on a map
 
   |Omschrijving=Visualizing atmospheric particulate matter concentrations on a map
   |Status=In progress
+
   |Status=Completed
 
   |Contact=bertrik
 
   |Contact=bertrik
 
   }}
 
   }}
 +
 +
== How can you help ==
 +
What would help me:
 +
* create a nice black-and-white background map (png) with equirectangular projection of an area larger than just the netherlands (e.g. containing also Belgium, perhaps part of west Germany, Ruhr-area). I would need the exact lat/lon coordinates of the area.
  
 
== Introduction ==
 
== Introduction ==
This page is about creating a 'stofradar' image of atmospheric particulate matter concentrations based on the raw data measured by the luftdaten.info network,
+
This page is about creating a 'stofradar' image of atmospheric particulate matter concentrations based on the raw data measured by the sensor.community network,
 
see [http://www.stofradar.nl www.stofradar.nl].
 
see [http://www.stofradar.nl www.stofradar.nl].
  
Line 16: Line 20:
 
See also my [[DustSensor]] page.
 
See also my [[DustSensor]] page.
  
The website [https://luftdaten.info luftdaten.info] is an initiative to allow citizens to participate in measuring atmospheric particulate matter concentration using an inexpensive and [https://luftdaten.info/nl/sensor-bouwen/ easy to build sensor].
+
The website [https://sensor.community sensor.community] is an initiative to allow citizens to participate in measuring atmospheric particulate matter concentration using an inexpensive and [https://sensor.community/nl/sensor-bouwen/ easy to build sensor].
 
They collect this data, calculate 5 minute and daily averages and publish it again as open data.
 
They collect this data, calculate 5 minute and daily averages and publish it again as open data.
The total number of sensors is > 5000 worldwide, most of them in Germany, Bulgaria, Belgium, Austria, Sweden.
+
The total number of sensors is > 6000 worldwide, most of them in Germany, Bulgaria, Belgium, Austria, Sweden.
 
The Netherlands has about 100 sensors.
 
The Netherlands has about 100 sensors.
  
 
Future activities:
 
Future activities:
 +
* plot PM2.5 and apply humidity correction
 +
* plot official [https://www.luchtmeetnet.nl/ luchtmeetnet] measurements on the map too, access to the API has been implemented:[https://github.com/bertrik/luftdatenmapper/tree/master/workspace/luftdatenmapper/src/main/java/nl/bertriksikken/luchtmeetnet/api work in progress]
 +
 +
* re-add a blacklist so we can suppress known bad measurement stations
 
* use an OSM background map
 
* use an OSM background map
 
* improve fine alignment between map and dust overlay
 
* improve fine alignment between map and dust overlay
 
* create a map of a larger area, including germany (it has a lot of data points)
 
* create a map of a larger area, including germany (it has a lot of data points)
* add a distance limit to how far away measurement can be to influence the concentration (e.g. max 30 km), mark areas with no coverage
+
* review and update stats mentioned above (e.g. "100 sensors in netherlands")
 +
* verify that gzip compression is used on the sensor.community JSON download
  
 
== Visualisation ==
 
== Visualisation ==
Line 44: Line 53:
 
So a nearby sensor has a large effect and a far away sensor has very little effect, contributing only a little bit to the global average.
 
So a nearby sensor has a large effect and a far away sensor has very little effect, contributing only a little bit to the global average.
  
To calculate the distance<sup>2</sup>, I use a very simple approximation:
+
To calculate the distance, I use a very simple approximation:
* determine the difference in longitude and latitude
+
* calculate the "middle" of the map (average latitude/longitude between top-left and bottom-right);
* apply an 'aspect ratio' factor of cos(latitude) to the longitude difference. I use the latitude of the approximate middle of the netherlands (52.2 lat, 5.3 lon) to calculate this aspect ratio factor.  
+
* calculate the "km-per-degree-latitude" at the middle for latitude as 40000 km / 360 degrees;
* distance<sup>2</sup> = (difference latitude)<sup>2</sup> + (difference longitude)<sup>2</sup>
+
* calculate the "km-per-degree-longitude" at the middle for longitude as the number above multiplied with cos(latitude);
 +
* determine the difference in longitude and the difference in latitude;
 +
* convert both to km using the factors calculated earlier;
 +
* calculate the [https://en.wikipedia.org/wiki/Euclidean_distance euclidean distance].
 
A better way would be to use the  
 
A better way would be to use the  
 
[https://en.wikipedia.org/wiki/Great-circle_distance 'great-circle-distance'] and possibly even account for the fact that the earth is not perfectly spherical, but I like to start simple and this makes the calculation a lot faster.
 
[https://en.wikipedia.org/wiki/Great-circle_distance 'great-circle-distance'] and possibly even account for the fact that the earth is not perfectly spherical, but I like to start simple and this makes the calculation a lot faster.
 +
 +
Pixels that are not within a certain distance of any sensor station (e.g. 25 km) are rendered as grayscale, to indicate a geographic limit of each sensor.
 +
 +
Only sensors within a reasonable range of the map are taken into account, currently this is an area of 9 times (3x3) the visible area.
  
 
PM10 values higher than 500 ug/m3 are simply ignored in the software.
 
PM10 values higher than 500 ug/m3 are simply ignored in the software.
Line 68: Line 84:
 
The effect become really significant above approximately 70% humidity.
 
The effect become really significant above approximately 70% humidity.
  
An interesting idea is to try to compensate for this effect, since the luftdaten sensor has an onboard humidity-sensor.
+
An interesting idea is to try to compensate for this effect, since the sensor.community sensor has an onboard humidity-sensor.
 
Some papers/links about this:  
 
Some papers/links about this:  
 
* https://www.samenmetenaanluchtkwaliteit.nl/sites/default/files/2018-07/Status_SDS011_12juli18.pdf
 
* https://www.samenmetenaanluchtkwaliteit.nl/sites/default/files/2018-07/Status_SDS011_12juli18.pdf
Line 75: Line 91:
  
 
However, I see the following problems with the formulas and coefficient in the opendata-stuttgart link above:
 
However, I see the following problems with the formulas and coefficient in the opendata-stuttgart link above:
* it combines formulas and coefficients from different sources where relative humidity has different units. One paper seems to use an RH-value from 0 to 100, while another uses a kind of normalized relatively humidity (from 0 to 1). You cannot just use the same coefficients if the unit is different.
+
* it combines formulas and coefficients from different sources where relative humidity has different units. One paper seems to use an RH-value from 0 to 100, while another uses a kind of normalized relative humidity (from 0 to 1). You cannot just use the same coefficients if the unit is different.
 
* it claims a humidity correction for PM10 with coefficients that is not found in the source paper.
 
* it claims a humidity correction for PM10 with coefficients that is not found in the source paper.
  

Revision as of 17:53, 21 October 2020

Project Stofradar
Stofradar3.png
Visualizing atmospheric particulate matter concentrations on a map
Status Completed
Contact bertrik
Last Update 2020-10-21

How can you help

What would help me:

  • create a nice black-and-white background map (png) with equirectangular projection of an area larger than just the netherlands (e.g. containing also Belgium, perhaps part of west Germany, Ruhr-area). I would need the exact lat/lon coordinates of the area.

Introduction

This page is about creating a 'stofradar' image of atmospheric particulate matter concentrations based on the raw data measured by the sensor.community network, see www.stofradar.nl.

The focus is on raw visualisation of the source data, only the most minimal attempt is made to "validate" the data. Sensor measurements and sensor locations are basically uncontrolled, since we cannot tell if a particular sensor is defective or has an unusual position that affects its measurements.

See also my DustSensor page.

The website sensor.community is an initiative to allow citizens to participate in measuring atmospheric particulate matter concentration using an inexpensive and easy to build sensor. They collect this data, calculate 5 minute and daily averages and publish it again as open data. The total number of sensors is > 6000 worldwide, most of them in Germany, Bulgaria, Belgium, Austria, Sweden. The Netherlands has about 100 sensors.

Future activities:

  • plot PM2.5 and apply humidity correction
  • plot official luchtmeetnet measurements on the map too, access to the API has been implemented:work in progress
  • re-add a blacklist so we can suppress known bad measurement stations
  • use an OSM background map
  • improve fine alignment between map and dust overlay
  • create a map of a larger area, including germany (it has a lot of data points)
  • review and update stats mentioned above (e.g. "100 sensors in netherlands")
  • verify that gzip compression is used on the sensor.community JSON download

Visualisation

The general idea is to create an image, with a map at the background and the atmospheric particulate matter concentration overlaid on top.

Background map

Pages to investigate:

What I need/want is to be able to specify the 'bounding box' and use a equirectangular projection , so I can easily map a pixel back to a latitude/longitude.

Interpolation

Since we only have data at a set of discrete points, the concentration at other points is estimated by combining data from all sensors using inverse distance weighting, in particular using the distance *squared* as the weighing factor in a weighted average. So a nearby sensor has a large effect and a far away sensor has very little effect, contributing only a little bit to the global average.

To calculate the distance, I use a very simple approximation:

  • calculate the "middle" of the map (average latitude/longitude between top-left and bottom-right);
  • calculate the "km-per-degree-latitude" at the middle for latitude as 40000 km / 360 degrees;
  • calculate the "km-per-degree-longitude" at the middle for longitude as the number above multiplied with cos(latitude);
  • determine the difference in longitude and the difference in latitude;
  • convert both to km using the factors calculated earlier;
  • calculate the euclidean distance.

A better way would be to use the 'great-circle-distance' and possibly even account for the fact that the earth is not perfectly spherical, but I like to start simple and this makes the calculation a lot faster.

Pixels that are not within a certain distance of any sensor station (e.g. 25 km) are rendered as grayscale, to indicate a geographic limit of each sensor.

Only sensors within a reasonable range of the map are taken into account, currently this is an area of 9 times (3x3) the visible area.

PM10 values higher than 500 ug/m3 are simply ignored in the software.

Colour range

The colours I'm using (a kind of inverted spectral range from blue to red):

  • 0 ug/m3: fully transparent white (#FFFFFF)
  • 25 ug/m3: semi-transparent cyan (#00FFFF)
  • 50 ug/m3: semi-transparent yellow (#FFFF00). This is the threshold for the maximum daily average for PM10 in the Netherlands.
  • 100 ug/m3: semi-transparent red (#FF0000)
  • 200 ug/m3 and higher: semi-transparent purple (#FF00FF)

Values in between these levels are interpolated linearly with respect to the RGB colour value and alpha channel.

This scale is approximately logarithmic, with each step being twice as big as the previous one.

Correction for high humidity

Humidity generally seems to cause an overestimation of PM measurements for measurements done with a "particle counting" type of PM sensor. The effect become really significant above approximately 70% humidity.

An interesting idea is to try to compensate for this effect, since the sensor.community sensor has an onboard humidity-sensor. Some papers/links about this:

However, I see the following problems with the formulas and coefficient in the opendata-stuttgart link above:

  • it combines formulas and coefficients from different sources where relative humidity has different units. One paper seems to use an RH-value from 0 to 100, while another uses a kind of normalized relative humidity (from 0 to 1). You cannot just use the same coefficients if the unit is different.
  • it claims a humidity correction for PM10 with coefficients that is not found in the source paper.

Compositing

I use imagemagick for this, for example:

 composite -compose over -geometry 600x800 20180605_210100.json.png netherlands.png output.png

where netherlands.png is an 600x800 opaque black-and-white image of the map of the netherlands and 20180605_210100.json.png is an 60x80 image of dust concentrations with an alpha channel

Animation

The idea of animation is to combine several 5-minute images into a movie.

There are several options and file formats to choose from:

  • GIF appears way too big, resulting in files of about 40 MB for 288 frames.
  • APNG is only slighty smaller at about 37 MB.
  • the webm format seems more suited, can be less than 1MB (lossy, VP9).

Example conversion command for webm:

 cat ~/luftdatenmapper/tmp/netherlands/*.png |ffmpeg -f image2pipe -r 12 -i - -b:v 200k netherlands.webm

This results in an output file of about 650 kB.

Software

See the github page for the source code.