Difference between revisions of "StofAnanas"

From RevSpace
Jump to navigation Jump to search
(The idea)
(The idea)
Line 14: Line 14:
  
 
Features:
 
Features:
* The lamp shows particulate matter concentration as a colour, from dark blue for low concentration to bright pink for high concentration
+
* The lamp shows PM10 particulate matter concentration as a colour, from dark blue for low concentration to bright pink for high concentration
* The lamp retrieves the PM value over wifi from the the luftdaten website
+
* The lamp retrieves the PM value over wifi from the the luftdaten website, there is a one-time setup to configure your WiFi network so the device can access the internet
* The luftdaten measurement station used for the PM concentration can be entered at the same time as when wifi credentials are entered.
+
* The number/id of the luftdaten station used for the PM concentration can to be entered during the one-time setup.
* If no luftdaten station is entered, the luftdaten measurement station is determined automatically by geolocating based on nearby WiFi access points!
+
* If no luftdaten station id is entered, the station id is determined automatically by WiFi geolocation!
* Made compatible with [https://nl.aliexpress.com/item/32891674707.html Wemos D1 RGB LED shields]. My PL9823 LED appears to be compatible with the WS2812B LED driver.
+
* The hardware setup is compatible with [https://nl.aliexpress.com/item/32891674707.html Wemos D1 RGB LED shields]. My PL9823 LED is compatible with the WS2812B LED driver.
  
 
Ideas/nice to have:
 
Ideas/nice to have:

Revision as of 11:46, 3 July 2019

Project StofAnanas
StofAnanas.jpg
Showing particulate matter concentration as a coloured light
Status In progress
Contact bertrik
Last Update 2019-07-03

The idea

Show current airborne particulate matter concentration using a LED light in a lamp, inspired by http://stoflamp.nl The data that the LED colour is based on is simply retrieved over WiFi from the luftdaten website.

This lamp is a soft plastic translucent pine apple ("ananas"), bought at the "Action" store.

Features:

  • The lamp shows PM10 particulate matter concentration as a colour, from dark blue for low concentration to bright pink for high concentration
  • The lamp retrieves the PM value over wifi from the the luftdaten website, there is a one-time setup to configure your WiFi network so the device can access the internet
  • The number/id of the luftdaten station used for the PM concentration can to be entered during the one-time setup.
  • If no luftdaten station id is entered, the station id is determined automatically by WiFi geolocation!
  • The hardware setup is compatible with Wemos D1 RGB LED shields. My PL9823 LED is compatible with the WS2812B LED driver.

Ideas/nice to have:

  • The lamp "breathes" by varying the intensity over time, e.g. a cycle of 10 seconds where the light dims a bit and brightens a bit
    • perhaps increase the breathing rate for higher PM?
    • perhaps modulate the colour saturation instead of intensity?
  • Remote control over IR?

Operation Manual

configuration

Programming

  • connect everything up as indicated under 'hardware' and connect the Wemos D1 board to the USB port of your development PC / laptop
  • flash the software into the Wemos D1 mini, typically from the command line using platformio:
 pio run -t upload

Configuration

Automatic configuration:

  • move close to the particulate matter sensor (< 100 meters), power up the lamp
  • on a mobile phone, connect to the "ESP-STOFANANAS" network, and select login
  • when presented with the captive portal, select a WiFi network, fill in the WiFi password, leave the luftdaten id field empty, press SAVE
  • the closest particulate matter sensor will automatically be determined

Manual configuration:

  • on https://netherlands.maps.luftdaten.info find the particulate matter station you want to follow and note the number of the station, for example "12246"
  • on a mobile phone, connect to the "ESP-STOFANANAS" network, and select login
  • when presented with the captive portal, select a WiFi network, fill in the WiFi password, AND ALSO fill in the number you looked up earlier, press SAVE

Alternatively:

  • move close to the particulate matter sensor (< 100 meters) and make sure at least the WiFi credentials have been entered and saved
  • open a console to the serial port (115200 bps) and enter the following command:
 config auto
  • within a few seconds, you should see it prints the current approximate geographic location and the id of the luftdaten station, the id should be non-zero

Usage

  • Power up the lamp while in range of the WiFi network you configured
  • The LED should start yellow (connecting to the WiFi), then briefly change to OFF (retrieving PM value from Luftdaten), then change to a colour representing a PM concentration
  • A new PM measurement is retrieved every 5 minutes.

Hardware

pinout

The lamp is controlled by an ESP8266, a Wemos D1 mini board. The LED is an RGB LED with built-in PL9823 controller. The PL9823 is compatible with the WS2812B RGB LED as far as I can tell (the WS2812B driver in the FastLED library works with the PL9823).

Connections (using dupont female-female):

  • LED Din to Wemos D1 mini pin D2
  • LED Gnd to Wemos D1 mini pin GND
  • LED Vdd to Wemos D1 mini pin 5V

This is the same pinout as used by the Wemos WS2812B RGB shield

Software

Getting and building the source code

Source code is available on github.

To compile and upload it, I use platform io:

 pio run -t upload

You can also compile it with the Arduino IDE, libraries used:

  • WiFiManager (v 0.14) is used to manage WiFi connection to the local AP
  • ArduinoJSON (v 6.11) for the parsing the luftdaten response
  • FastLED (v 3.2.9) is used to control the RGB LED

Luftdaten interface

The current measurement value of a particular sensor can be determined by parsing the JSON messages retrieved over a REST interface, by performing an HTTP GET on URL

 http://api.luftdaten.info/v1/sensor/<sensor-id>/

where <sensor-id> is the database id used by luftdaten (and visible on their map). The trailing slash in the URL is significant.

For example:

 http://api.luftdaten.info/v1/sensor/12246/

The software looks for the "P1" (PM10) sensor value in the JSON message and averages all measurements it finds (usually the current one and a previous one).

Colour mapping

Mapping is as follows, with piecewise linear interpolation:

  • 0 ug/m3: deep blue
  • 25 ug/m3: green
  • 50 ug/m3: yellow
  • 100 ug/m3: red
  • 200 ug/m3: (and higher)purplish