Difference between revisions of "StofAnanas"

From RevSpace
Jump to navigation Jump to search
(Software)
(The idea)
Line 11: Line 11:
 
The data that the LED colour is based on is simply retrieved over WiFi from the luftdaten website.
 
The data that the LED colour is based on is simply retrieved over WiFi from the luftdaten website.
  
This lamp is a plastic pine apple ("ananas"), bought at the "Action" store.
+
This lamp is a soft plastic translucent pine apple ("ananas"), bought at the "Action" store.
  
 
Features:
 
Features:
* The lamp shows particulate matter concentration as a colour, from dark blue for low concentration and bright pink for high concentration
+
* The lamp shows particulate matter concentration as a colour, from dark blue for low concentration to bright pink for high concentration
 
* The lamp retrieves the PM value over wifi from the the luftdaten website
 
* The lamp retrieves the PM value over wifi from the the luftdaten website
 
* The luftdaten measurement station can be entered at the same time as when wifi credentials are entered.
 
* The luftdaten measurement station can be entered at the same time as when wifi credentials are entered.

Revision as of 22:05, 20 June 2019

Project StofAnanas
StofAnanas.jpg
Showing particulate matter concentration as a coloured light
Status In progress
Contact bertrik
Last Update 2019-06-20

The idea

Show current airborne particulate matter concentration using a LED light in a lamp, inspired by http://stoflamp.nl The data that the LED colour is based on is simply retrieved over WiFi from the luftdaten website.

This lamp is a soft plastic translucent pine apple ("ananas"), bought at the "Action" store.

Features:

  • The lamp shows particulate matter concentration as a colour, from dark blue for low concentration to bright pink for high concentration
  • The lamp retrieves the PM value over wifi from the the luftdaten website
  • The luftdaten measurement station can be entered at the same time as when wifi credentials are entered.
  • should be compatible with Wemos D1 RGB LED shields. My PL9823 LED appears to be compatible with WS2812B LEDs.

Ideas/nice to have:

  • The lamp "breathes" by varying the intensity over time, e.g. a cycle of 10 seconds where the light dims a bit and brightens a bit
    • perhaps increase the breathing rate for higher PM
    • perhaps modulate the colour saturation instead of intensity
  • Automatic determination of location by means of wifi location, so you don't even need to input a luftdaten monitoring station id (do this on every startup for example)
    • example query to get (very coarse) position data from Mozilla:
 https://location.services.mozilla.com/v1/geolocate?key=test
    • example query to list of sensors centered around a location from Luftdaten:
 http://api.luftdaten.info/v1/filter/area=52.022,4.692,1.0
  • Remote control over IR

Operation Manual

configuration

Programming

  • connect everything up as indicated under 'hardware' and connect the Wemos D1 board to the USB port of your development PC / laptop
  • flash the software into the Wemos D1 mini, typically from the command line using platformio:
 pio run -t upload

Configuration

  • on https://netherlands.maps.luftdaten.info find the particulate matter station you want to follow and note the number of the station, for example "12246"
  • on a mobile phone, connect to the "ESP-STOFANANAS" network, and select login
  • when presented with the captive portal, select a WiFi network, fill in the WiFi password, AND ALSO fill in the number you looked up earlier, press SAVE
  • NOTE: when the configuration is ongoing, the LED will be YELLOW, it turns OFF when configuration is done.

Usage

  • POwer up the lamp while in range of the WiFi network you configured
  • The LED should start yellow (connecting to the WiFi), then briefly change to OFF (retrieving PM value from Luftdaten), then change to a colour representing a PM concentration
  • A new PM measurement is retrieved every 5 minutes.

Hardware

pinout

The lamp is controlled by an ESP8266, a Wemos D1 mini board. The LEDs is an RGB LED with built-in PL9823 controller.

Connections (using dupont female-female):

  • LED Din to Wemos D1 mini pin D3
  • LED Gnd to Wemos D1 mini pin GND
  • LED Vdd to Wemos D1 mini pin 5V

Software

Getting and building the source code

Source code is available on github.

To compile and upload it, I use platform io:

 pio run -t upload

You can also compile it with the Arduino IDE, libraries used:

  • WiFiManager (v 0.14) is used to manage WiFi connection to the local AP
  • ArduinoJSON (v 6.11) for the parsing the luftdaten response
  • FastLED (v 3.2.9) is used to control the RGB LED

Luftdaten interface

The current measurement value of a particular sensor can be determined by parsing the JSON messages retrieved over a REST interface, by performing an HTTP GET on URL

 http://api.luftdaten.info/v1/sensor/<sensor-id>/

where <sensor-id> is the database id used by luftdaten (and visible on their map). The trailing slash in the URL is significant.

For example:

 http://api.luftdaten.info/v1/sensor/12246/

The software looks for the "P1" (PM10) sensor value in the JSON message and averages all measurements it finds (usually the current one and a previous one).

Colour mapping

Mapping is as follows, with piecewise linear interpolation:

  • 0 ug/m3: deep blue
  • 25 ug/m3: green
  • 50 ug/m3: yellow
  • 100 ug/m3: red
  • 200 ug/m3 (and higher): pink