LoraWanDustSensor: Difference between revisions

From RevSpace
Jump to navigation Jump to search
Line 60: Line 60:


== Software ==
== Software ==
Source code:
=== Source code ===
* [https://github.com/bertrik/LoraWanPmSensor Arduino node]
* [https://github.com/bertrik/LoraWanPmSensor Arduino node]
* [https://github.com/bertrik/LoraLuftdatenForwarder TTN-to-luftdaten forwarder]
* [https://github.com/bertrik/LoraLuftdatenForwarder TTN-to-luftdaten forwarder]


=== Common ===
=== Common ===

Revision as of 21:28, 22 April 2019

Project LoRaWAN dust Sensor
LoraWanDustSensor.jpg
LoRaWAN airborne particulate matter sensor
Status In progress
Contact bertrik
Last Update 2019-04-22


The plan

The plan is to create a system consisting of:

  • a sensor that measures airborne particulate matter and sends the measurement data using LoRa/TheThingsNetwork to a central location.
  • a backend that collects the data from TTN and forwards it to luftdaten.info

This has been done before by other people, but I can't figure out the 'best' solution:

  • source code location is obscure, I will publish all source code on github and put up documentation on this wiki
  • everyone invents their own payload format, I'd like to use something relatively universal and standard, so I think I will try to use the Cayenne LPP format.

This has been done by TTN Ulm, see https://github.com/verschwoerhaus/ttn-ulm-feinstaub (the sensor code) and https://github.com/verschwoerhaus/ttn-ulm-muecke (the forwarder, in python)

Sensors join the network using OTAA (instead of ABP), that way I try to minimize the setup of each individual node. All nodes use the same application EUI and the same application key.

So I'd like to just re-invent the wheel properly this time.

Next steps

  • Investigate failing re-joins that seem to happen some time after the node has been online
  • Implement a kind of schedule: turn the sds011 on, wait some time, take a measurement, turn it off, wait for some time
    • make this match the TTN send schedule? it's useless to do a measurement if we don't have TTN airtime to transmit it
  • Finish the Java software (MQTT listener, payload decoder, luftdaten forwarder)

Dump

Useful links for the TTGO LoRa board:

Hardware

The node is based on Arduino, in particular a TTGO ESP32 board with onboard LoRa chip. The sensor is an SDS-011, just like in the luftdaten project.

NOTE: https://www.thethingsnetwork.org/community/berlin/post/warning-attention-users-of-ttgo21-v16-boards-labeled-t3_v16-on-pcb-battery-exploded-and-got-on-fire

Page with correct pinout of the ESP32 LoRa board.

Luftdaten uses a cycle time of 145 seconds for the SDS011.

Proposed hardware connections:

  • SDS011 5V to ESP32 5V
  • SDS011 GND to ESP32 GND
  • SDS011 TXD to ESP32 GPIO25 (maybe I can find two suitable pins close together)
  • SDS011 RXD to ESP32 GPIO34 (maybe I can find two suitable pins close together)
  • BME280 3V todo
  • BME280 SDA todo
  • BME280 SCL todo
  • BME280 GND todo

Software

Source code

Common

Packet format

Proposed structure of packets transferred over LoRa:

  • PM10 value, encoded in units of 0.1 ug/m3: 2 bytes
  • PM2.5 value, encoded in units of 0.1 ug/m3: 2 bytes
  • temperature, encoded in units of 0.1 deg C: 2 bytes
  • relative humidity, encoded in units of 0.1%, 2 bytes

Total: 8 bytes

Not present value is 0xFFFF. Encoding is big endian.

Would be nice to use Cayenne for this, but I don't know if Cayenne has an id for particulate matter.

How other projects encode the data:

Node

Source code for the particulate matter measurement node can be found on the github page.

platformio

To compile and upload the code to the node, platformio is used.

To install platformio (example for Debian):

 sudo apt-get install python-pip
 sudo pip install platformio
 pio update

To compile and upload:

 pio run -t upload

design

The function of the node software is to collect data from the SDS011 (particulate matter) and BME280 (temperature/humidity) at regular intervals, encode this as a data packet and send it over LoRaWAN towards TheThingsNetwork.

For the LoRaWAN data connection, over-the-air activation (OTAA) is used. I use the following scheme, to keep administration to a minimum:

  • The Device EUI is derived from the ESP32 MAC address, the node shows this on its OLED
  • The App EUI is generated in the TTN console, it is the same for all nodes
  • The App Key is generated in the TTN console, it is the same for all nodes
  • The device is registered in the TTN console by the Device EUI (this doesn't happen automatically). Frame counter checks are disabled.
  • OTAA is done only once for each node. After that, the OTAA parameters are stored in (simulated) EEPROM.
    • Perhaps with a long press on the button, we can reset the OTAA?
  • OTAA progress is shown on the OLED
  • If OTAA has been done successfully, the node restores the session parameters negotiated during OTAA on next bootup, so it can quickly resume sending data.
  • I'm NOT saving the upload frame counter (this would be preferable), just disable the feature in the TTN console.

TODO to figure out:

  • What about the channel setup? The node connects using 3 frequencies, but receives a bigger list of frequencies during OTAA JOIN.

I've seen the following from the node, receiving an ADR:

 40829907: engineUpdate, opmode=0x8
 40829935: EV_TXSTART
 40829939: engineUpdate, opmode=0x888
 40830013: TXMODE, freq=868300000, len=25, SF=11, BW=125, CR=4/5, IH=0
 40944876: setupRx1 txrxFlags 0x22 --> 01
 start single rx: now-rxtime: 5
 40945013: RXMODE_SINGLE, freq=868300000, SF=11, BW=125, CR=4/5, IH=0
 rxtimeout: entry: 40951170 rxtime: 40945001 entry-rxtime: 6169 now-entry: 5 rxtime-txend: 63524
 41005584: setupRx2 txrxFlags 0x1 --> 02
 start single rx: now-rxtime: 4
 41005720: RXMODE_SINGLE, freq=869525000, SF=9, BW=125, CR=4/5, IH=0
 41017003: process options (olen=0x5)
 41017012: LinkAdrReq: p1:11 chmap:00ff chpage:00 uprt:01 ans:86
 41017019: ??ack error ack=1 txCnt=0
 41017073: decodeFrame txrxFlags 0x2 --> 22
 41017312: Received downlink, window=RX2, port=-1, ack=1, txrxFlags=0x22
 41017708: EV_TXCOMPLETE (includes waiting for RX windows)
 41018027: engineUpdate, opmode=0x800

Backend

A Java program subscribes to the MQTT stream, decodes the telemetry packets and forwards them to the luftdaten API. There is no storage of measurement data in the Java application.

I've already developed some Java code that publishes the measurement values towards luftdaten.info. Also I've developed code before to subscribe to the TTN MQTT stream.

To receive data using mosquitto:

 mosquitto_sub -h eu.thethings.network -p 1883 -t +/devices/+/up -u particulatematter -P ttn-account-v2.cNaB2zO-nRiXaCUYmSAugzm-BaG_ZSHbEc5KgHNQFsk

Example upstream data:

 particulatematter/devices/ttgo_mac/up {"app_id":"particulatematter","dev_id":"ttgo_mac","hardware_serial":"000084B14CA4AE30","port":1,"counter":16,"payload_raw":"AAEALAAd/////w==","metadata":{"time":"2019-04-13T08:37:45.338427686Z","frequency":868.3,"modulation":"LORA","data_rate":"SF11BW125","airtime":823296000,"coding_rate":"4/5","gateways":[{"gtw_id":"eui-008000000000b8b6","timestamp":2000599916,"time":"2019-04-13T08:37:45.320735Z","channel":1,"rssi":-115,"snr":-3,"rf_chain":1,"latitude":52.0182,"longitude":4.70844,"altitude":27}]}}

Example downstream data:

 particulatematter/devices/ttgo_mac/events/down/sent {"payload":"YPUvASalGgEDEf8AAcqtmOw=","message":{"app_id":"particulatematter","dev_id":"ttgo_mac","port":0},"gateway_id":"eui-008000000000b8b6","config":{"modulation":"LORA","data_rate":"SF9BW125","airtime":164864000,"counter":282,"frequency":869525000,"power":27}}