LoRa-E5-mini

From RevSpace
Revision as of 10:57, 10 October 2021 by Bertrik Sikken (talk | contribs) (Getting it to work)
Jump to navigation Jump to search
Project LoRa E5
Arduino on the LoRa-E5 module
Status In progress
Contact bertrik
Last Update 2021-10-10

The plan

This page is about the LoRa-E5 module and getting it to work as a LoRaWAN node with Arduino and the BasicMac stack.

  • replace the original "AT" firmware with Arduino based firmware
  • use the BasicMac library for LoRaWAN
  • use platformio as the build system
  • create some basic examples for use as a LoRaWAN node on TheThingsNetwork

Interesting post about this module: https://www.disk91.com/2021/technology/lora/lora-e5-the-seeed-studio-stm32-wl-module/

Hardware

The hardware is the LoRa-E5 module from seeed studio, contains the STM32WLE5JC:

Overview of pins used on this board (not completely standard): https://wiki.seeedstudio.com/LoRa_E5_mini/#22-gpio-configuration-overview

Software

https://github.com/bertrik/lora-e5

There appears to be support for various kinds of WL55 boards: https://github.com/stm32duino/Arduino_Core_STM32/blob/main/boards.txt

Support for this board in this archive: https://github.com/dolfandringa/Arduino_Core_STM32/blob/master/variants/STM32WLxx/WL54JCI_WL55JCI_WLE4J(8-B-C)I_WLE5J(8-B-C)I/boards_entry.txt#L62 ???

Development environment

Load the .ino file. Compile with ctrl-R. Upload with ctrl-U.

Programming over SWD

Connect an ST-LINKv2 as follows:

  • SWDIO to PA13
  • SWCLK to PA14
  • GND to GND

Hold BOOT, then press RST and execute:

 openocd -s /usr/share/openocd/scripts -f interface/stlink.cfg -f target/stm32wlx.cfg

Result:

Open On-Chip Debugger 0.11.0
Licensed under GNU GPL v2
For bug reports, read
	http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
Info : clock speed 500 kHz
Info : STLINK V2J17S4 (API v2) VID:PID 0483:3748
Info : Target voltage: 3.258730
Info : stm32wlx.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : starting gdb server for stm32wlx.cpu on 3333
Info : Listening on port 3333 for gdb connections

Or program over serial?

Getting it to work

Got a flashing LED sketch to work:

  • install Arduino IDE, e.g. 1.8.16
  • install the STM32 support
    • add through menu File / Preferences / Additional board manager URLs
 https://github.com/stm32duino/BoardManagerFiles/raw/main/package_stmicroelectronics_index.json
    • under menu Tools / Board / Board manager, search for stm32 and install the board package
  • select the right board:
    • WLE5JCIx
  • upgrade the firmware of my stlink2 (tool from ST), currently at V2J38S7
  • run the cubestm environment to use the stlink2 to disable the firmware protection
  • flash a simple blinky sketch to the board

Serial port does not work yet, it is connected to PB6/PB7. I need to configure an alternative setting for the pins, don't know exactly how to do that on Arduino:

Node configuration in TheThingsNetwork

The information on the website of Seeed studios is outdated. It refers to the "v2" version of TheThingsNetwork, which is being phased out. It is already impossible to add new nodes on TTNv2, since it was set to read-only.

Nodes should be configured for TheThingsNetwork v3 instead.