Esp32cam: Difference between revisions

From RevSpace
Jump to navigation Jump to search
No edit summary
 
(11 intermediate revisions by 3 users not shown)
Line 3: Line 3:
   |Picture=ESP32-CAM.jpg
   |Picture=ESP32-CAM.jpg
   |Omschrijving=Cheap webcams with Wifi, what could possibly go wrong?
   |Omschrijving=Cheap webcams with Wifi, what could possibly go wrong?
   |Status=Initializing
   |Status=In progress
   |Contact=noopwafel
   |Contact=noopwafel
   |Contact1=Sebastius
   |Contact1=bertrik
   }}
   }}




== Introduction ==
It's an ESP32 board with a camera, running a web server, so it acts as an inexpensive webcam.
== Hardware ==
* http://wiki.aithinker.com/esp32-cam
* http://wiki.aithinker.com/esp32-cam
* [[bertrik]] ordered [https://aliexpress.com/item/ESP32-CAM/32947577882.html this board on AliExpress]
To install the camera:
* flip the black part of the camera connector 90 degrees so it points up
* place the camera connector, contacts towards the PCB, camera facing up
* gently slide the connector in place (about 2 or 3 mm of travel), e.g. pushing with the screw driver onto the rigid part of the camera connector towards the white part of the PCB connector
* flip the black part of the connector back into the flat position.
Pins (ESP32 cam to USB serial converter):
* ESP-32 5V to USB serial 5V
* ESP-32 GND to USB serial GND
* ESP-32 UAR to USB-serial TX
* ESP-32 UAT to USB-serial RX
* ESP-32 IO0 looped to ESP-32 GND (they are next to each other), you can use a jumper or a dupont wire. CLOSED for flashing, OPEN for running.
== Software ==
* maybe https://github.com/m5stack/m5stack-cam-psram ?
* https://github.com/donny681/ESP32_CAMERA_QR
* https://github.com/donny681/ESP32_CAMERA_QR
* maybe https://github.com/m5stack/m5stack-cam-psram ?
* [https://youtu.be/q7Z_XnBYFhY Step by step video guide to getting it up and running with Arduino IDE and the Expressif CameraWebServer example]
* https://github.com/geeksville/TenDollarWebcam
 
=== platformio ===
The CameraWebServer example can be compiled as a platformio project: https://github.com/bertrik/CameraWebServer
 
To build the code, clone the git repo above, cd into it, then type
  pio run
 
To upload it to the board (put a jumper between IO0 and GND):
  pio run -t upload
 
To watch the debug output (remove the jumper):
  pio device monitor
 
Platformio can be installed on a Debian Linux system as follows:
  sudo apt install python-pip
  sudo pip install platformio
  pio upgrade

Latest revision as of 14:49, 31 July 2021

Project ESP32-CAM
ESP32-CAM.jpg
Cheap webcams with Wifi, what could possibly go wrong?
Status In progress
Contact noopwafel, bertrik
Last Update 2021-07-31


Introduction

It's an ESP32 board with a camera, running a web server, so it acts as an inexpensive webcam.

Hardware

To install the camera:

  • flip the black part of the camera connector 90 degrees so it points up
  • place the camera connector, contacts towards the PCB, camera facing up
  • gently slide the connector in place (about 2 or 3 mm of travel), e.g. pushing with the screw driver onto the rigid part of the camera connector towards the white part of the PCB connector
  • flip the black part of the connector back into the flat position.

Pins (ESP32 cam to USB serial converter):

  • ESP-32 5V to USB serial 5V
  • ESP-32 GND to USB serial GND
  • ESP-32 UAR to USB-serial TX
  • ESP-32 UAT to USB-serial RX
  • ESP-32 IO0 looped to ESP-32 GND (they are next to each other), you can use a jumper or a dupont wire. CLOSED for flashing, OPEN for running.

Software

platformio

The CameraWebServer example can be compiled as a platformio project: https://github.com/bertrik/CameraWebServer

To build the code, clone the git repo above, cd into it, then type

 pio run

To upload it to the board (put a jumper between IO0 and GND):

 pio run -t upload

To watch the debug output (remove the jumper):

 pio device monitor

Platformio can be installed on a Debian Linux system as follows:

 sudo apt install python-pip
 sudo pip install platformio
 pio upgrade