Difference between revisions of "CubeCell"
Jump to navigation
Jump to search
(→Intro) |
(→Software) |
||
(5 intermediate revisions by the same user not shown) | |||
Line 19: | Line 19: | ||
* Use this board for my [[LoraBatBox]] | * Use this board for my [[LoraBatBox]] | ||
* [https://www.youtube.com/watch?v=lobNwqHLrag Video review by Andreas Spiess] | * [https://www.youtube.com/watch?v=lobNwqHLrag Video review by Andreas Spiess] | ||
− | |||
− | |||
− | |||
− | |||
− | |||
== Hardware == | == Hardware == | ||
Features: | Features: | ||
− | * based on an ASR605x (ARM cortex M0+ core) + SX1262 | + | * based on an ASR605x (ARM cortex M0+ core) + SX1262 radio chip |
* low power, only microamps sleep current | * low power, only microamps sleep current | ||
* battery connection | * battery connection | ||
Line 34: | Line 29: | ||
== Software == | == Software == | ||
+ | The CubeCell hardware works with (an export of) the [https://github.com/LacunaSpace/basicmac basicmac] device stack from Lacuna Space, just needs a pinmap definition, | ||
+ | (see also https://www.thethingsnetwork.org/forum/t/heltec-cubecell-part-2/37225/72): | ||
+ | <pre> | ||
+ | const lmic_pinmap lmic_pins = { | ||
+ | .nss = RADIO_NSS, | ||
+ | .tx = LMIC_CONTROLLED_BY_DIO2, | ||
+ | .rx = LMIC_UNUSED_PIN, | ||
+ | .rst = RADIO_RESET, | ||
+ | .dio = {LMIC_UNUSED_PIN, RADIO_DIO_1, LMIC_UNUSED_PIN}, | ||
+ | .busy = RADIO_BUSY, | ||
+ | .tcxo = LMIC_CONTROLLED_BY_DIO3, | ||
+ | }; | ||
+ | </pre> | ||
+ | |||
Example code: | Example code: | ||
− | * [https://github.com/HelTecAutomation/platform-asrmicro650x/blob/develop/examples/LoRa/LoRaWAN/LoRaWAN/src/LoRaWan.ino LoraWan example code] | + | * A basic working LoRaWAN platformio demo project is available at https://github.com/bertrik/cubecelldemo |
− | + | * [https://github.com/HelTecAutomation/platform-asrmicro650x/blob/develop/examples/LoRa/LoRaWAN/LoRaWAN/src/LoRaWan.ino LoraWan example code] from Heltec (not recommended) | |
− | |||
− | |||
− | |||
− | |||
− | |||
− |
Revision as of 09:37, 25 April 2021
Project CubeCell | |
---|---|
Low-power LoRaWAN Board | |
Status | In progress |
Contact | bertrik |
Last Update | 2021-04-25 |
Intro
This page is about the CubeCell board from heltec.org, aka HTCC-AB01
the github page for the Arduino code
What I'd like to investigate:
- Does it have an RTC? YES, it appears so
- --Can we run the arduino-lmic library on this? NO, probably not in the short term--
- --Can we compile the code with platformio? YES--
- Use this board for my LoraBatBox
- Video review by Andreas Spiess
Hardware
Features:
- based on an ASR605x (ARM cortex M0+ core) + SX1262 radio chip
- low power, only microamps sleep current
- battery connection
- solar cell connection
- pinout
Software
The CubeCell hardware works with (an export of) the basicmac device stack from Lacuna Space, just needs a pinmap definition, (see also https://www.thethingsnetwork.org/forum/t/heltec-cubecell-part-2/37225/72):
const lmic_pinmap lmic_pins = { .nss = RADIO_NSS, .tx = LMIC_CONTROLLED_BY_DIO2, .rx = LMIC_UNUSED_PIN, .rst = RADIO_RESET, .dio = {LMIC_UNUSED_PIN, RADIO_DIO_1, LMIC_UNUSED_PIN}, .busy = RADIO_BUSY, .tcxo = LMIC_CONTROLLED_BY_DIO3, };
Example code:
- A basic working LoRaWAN platformio demo project is available at https://github.com/bertrik/cubecelldemo
- LoraWan example code from Heltec (not recommended)